MoldMaking Technology

JUL 2018

Advertising in MoldMaking Technology offers

Issue link: https://mmt.epubxp.com/i/995639

Contents of this Issue

Navigation

Page 45 of 123

Mold Materials Hot Runners 44 MoldMaking Technology —— JULY 2018 This four-drop hot runner system has pressed-in tubular heaters. By David Hoffman and John Blundy Here are six important items to consider when evaluating a hot runner system: 1. Manifold heaters. For installation, most manufactur- ers use a press. If the heater contact with the manifold is not uniform, there will be hot spots created in the heater element, which causes premature failure and non-uniform heating of the manifold itself. Also, process capability can be affected especially with some engineering materials, as their viscosity may be more temperature sensitive than commodity resins like polypropylene and polyethylene. 2. Nozzle heaters. Measuring the ohm resistance for each nozzle heater can provide good information when troubleshoot- ing the hot runner system. Too great a variance may prevent uniform temperature profiles and the potential for process vari- ation will increase. Plus, the life of a heater with less efficiency is reduced because of the required increase in workload. 3. Nozzle tip orifice. Pressure differences in plastic injection molding are defined in the Hagen Poiseuille equation, where (Q) is the flow rate, (l) is the runner length, (n) is the material viscosity and (r) is the radius of the flow channel: ∆P=(8Qln)/ (πr 4 ). The equation shows that any slight difference in "r" value, which includes the orifice in a hot runner nozzle and gate tip, is affected to a magnitude of the fourth power. This means that a small change in radius will result in a rather large difference in pressure drop from gate tip to gate tip. The common perception is that if the gate tips are all within tolerance, this will not mat- ter. However, it is important to ask what the acceptable toler- ance is along with the gate tip dimensions. Just because they are within tolerance does not mean there will not be a difference in pressure drop. 4. Stack height. It is important to check the uniformity of the stack height across all nozzle tips. If these dimensions vary, then the engagement with the gate will also vary, and these variances could affect process capability because of resulting differences in channel geometry. Ask for the inspection report and consult the manifold supplier for an acceptable tolerance. Revisit the pressure drop equation to see if the tolerance that the supplier provides is acceptable for a given process and set of parts. 5. Flow channels. All gun drill manufacturers will claim vari- ances of 0.001 inch per inch of travel. Check that they can verify that the cross drilling of the flow channels does not leave a step at the intersection of the cross-drilled runners. Refer to the earlier equation again. Check that the gun drill manufacturer scoped and honed the channels. Variations in flow channels could create differences in pressure drop through the regions of a manifold. Again, this refers to the portion of the equation involving the radius (r), which is raised to the fourth power. Steps in the flow channel can create dead spots, which do not flush well when purging and cause color-change issues and material-degradation problems. Also, the steps make it possible for material to sit in the manifold for extended periods, which increases the likelihood for thermal degradation of the polymer. The polymer's natural flow path around the channel intersec- tions also causes these dead areas. This happens even if the channel intersections are perfectly aligned. 6. System cost. The cost of the system is often one of the most important things to consider, but relying solely on quotes from various suppliers is not the best way to approach the issue. Familiarity with the options that each hot runner supplier offers is helpful. Staying on top of the items presented here will reduce downtime, improve part quality and decrease overall costs. CONTRIBUTOR David Hoffman is a senior instructor and development manager for plastics education and training for the American Injection Molding Institute (AIM). John Blundy also contributed to this piece when he served as vice president of business development at Beaumont Technologies Inc. Pages 33 to 44 Six Key Factors for Evaluating a Hot Runner System Image courtesy of INCOE Corp. FOR MORE INFORMATION American Injection Molding Institute / 866-344-9694 / dhoffman@aim.institute / aim.institute Beaumont Technologies Inc. / 814-899-6390 / beaumontinc.com

Articles in this issue

Links on this page

Archives of this issue

view archives of MoldMaking Technology - JUL 2018