MoldMaking Technology

MAY 2017

Advertising in MoldMaking Technology offers

Issue link: https://mmt.epubxp.com/i/812778

Contents of this Issue

Navigation

Page 51 of 75

50 MoldMaking Technology —— MAY 2017 LEADTIME LEADER Q&A; How extensively do you use inspection and measure- ment technology in your shop, and where or how do you use it most? Have you invested in any new equip- ment recently? If yes, tell us about it. Krieger: I spent a day and a half researching inspection and metrology equipment firsthand during IMTS 2016. It was intriguing to see the world's finest manufacturers of inspection equipment in one place. I narrowed the deci- sion down to two brands and asked that they each make a presentation to share with my team, whose opinion I greatly value. Following the demonstrations of each product on our molds at the Krieger plant, we invested in a Faro blue light laser scanner and in the reverse engineering software, main- tenance and training for both. My vision is to utilize that technology to scan the block before it comes off the machine, inspect it as you go and know that it's right when it's deliv- ered for assembly. We don't have time to rework the rework when delivery seems to always be today, tomorrow, etc. Bral: We do on-machine inspection of parts, and most of our investments in inspection equipment have been for probes and software to make the inspection process more accurate and efficient. We also have checklists and certain operations that require signatures to make sure items are completed. We continue to research visual inspection equipment to further enhance inspection efficiency and also for reverse engineer- ing purposes. To me, this seems to be the area where scan- ning systems can be of the most benefit to moldmakers. We often do repair work to molds with no electronic data, and a scanning solution could recreate that data and improve our ability to work on these molds more effectively. How do you see inspection and measurement tech- nology evolving in the moldmaking industry over the next three to five years? Krieger: While I don't want to underestimate the guy who doesn't have all these fancy systems in place, it's only going to increase in importance because it's money—big money— especially when mistakes happen. Therefore, the intent is to attempt to catch mistakes "on the fly" as opposed to finding them when the end product is produced, and avoid addi- tional costs in both time and money, not to mention unnec- essary frustration for all involved. Prior to the introduction of standardized measurement to the manufacturing industry, mass chaos occurred and measurement became speculative, and from that, challenges of liability could—and did—arise. Whether you have your own metrology equipment or you have a third-party metrology source that can inspect parts for you, it's so important to utilize it, and provide evidence of accuracy to valued customers' engineering teams. It's also an insurance policy. Bral: In all honesty, as machines continue to improve in accuracy and quality, and our machining processes and techniques become more robust, I would hope there is a lower reliance on inspection and measurement in the future. Inspection is a non-value-added operation. It's also not an operation our customers directly pay us to do. If you can cut blocks reliably and know they will come together as intended in the end, there is no need to inspect; but as moldmakers, we need to be sure. The quality check that our custom- ers really care about is that the mold produces the part to print. Whether one side of a shutoff surface is 0.0001-inch heavy and the other side is 0.0001-inch light doesn't matter to them, as long as it shuts off and the part doesn't flash. I believe there will always be some level of inspection needed to verify operations were performed correctly, so we won't totally get away from it. EDITOR'S NOTES In this second of a series of regular columns, MoldMaking Technology invited last year's Leadtime Leader winner and honorable mention shops to share some of their thoughts about some hot industry topics. For more information on how to enter our Leadtime Leader Awards program, or if you have a question for any of the Leadtime Leaders, please e-mail Christina Fuges at cfuges@gardnerweb.com Krieger Craftsmen and MSI Mold Builders 2016 Leadtime Leader Honorable Mention Toby Bral, Sales Manager MSI Mold Builders Cedar Rapids, Iowa msimoldbuilders.com 2016 Leadtime Leader Winner Tim Krieger, President Krieger Craftsmen Grand Rapids, Michigan kriegercraftsmen.com

Articles in this issue

Links on this page

Archives of this issue

view archives of MoldMaking Technology - MAY 2017